EXPERIMENT 6 Molecular Fluorescence Spectroscopy: Quinine Assay

Department of Chemistry

University of Kentucky
EXPERIMENT 6

Molecular Fluorescence Spectroscopy: Quinine Assay



UNKNOWN

Submit a clean, labeled 500-mL volumetric flask to the instructor so that your unknown
quinine solution may be issued. Your name, section number, and your locker number
should be written legibly on this flask. The flask does not need to be dry on the inside, but
needs to have been rinsed with distilled water after it has been cleaned. The flask must be
turned in at least 1 lab period before you plan to do the experiment so that the Teaching
Assistants will have time to prepare the unknown. Each student will have his or her own
unknown to analyze even if you are working in pairs.


BACKGROUND

Quinine (C20H24N2O2, 324.43 g/mol) is an alkaloid extracted from the bark of the cinchona tree.
It has been used for many years as an antimalarial agent. Although it does not cure malaria, it is
effective in alleviating the symptoms of malarial attacks. The usual medicinal form is quinine
dihydrochloride or quinine sulfate dihydrate, (C20H24N2O2)2 H2SO4 2H2O, 782.97 g/mol.

Quinine is a very strongly fluorescing compound, especially in dilute acid solution, and thus can
be detected in very trace amounts. In 0.05 M H2SO4, quinine has two analytically useful
excitation wavelengths: λex = 250 and 350 nm. Regardless of which excitation wavelength is
used, the wavelength of maximum fluorescence emission intensity, λem or λfl, is 450 nm. The
basis for quantitation is that the intensity of fluorescence emission in very dilute solutions is
directly proportional to the concentration of quinine – if the intensity of the excitation source and
other experimental factors are kept constant. Because the absolute emission intensity can vary
considerably with small differences in experimental conditions, a calibration curve is prepared
by measuring the fluorescence-emission intensity of accurately known quinine standard
solutions.


INSTRUMENTATION

Turner Quantech Digital Filter Fluorometer, Model FM 109525

The instrument used in this experiment uses glass filters to select wavelength ranges appropriate
for quinine, rather than some type of expensive grating or prism monochromator to isolate
narrow excitation and fluorescence wavelengths. The latter type may typically have a bandpass
of 0.1 or 1 nm. A bandpass is defined as the width at half-height of the maximum intensity of
light that passes through the filter. It is also called the bandwidth.
CHE 226 – Analytical Chemistry Laboratory 34
Quinine
Fluorescence

---

Department of Chemistry

University of Kentucky

A monochromator-based instrument is much better for obtaining spectra, particularly those with
fine structure, but a filter-based unit will often be better for routine quantitative analysis. The
much larger bandpasses permit greater fractions of the excitation and fluorescent light to excite
the sample and to reach the detector, respectively. This greatly increases the sensitivity of the
instrument and can thus usually lower typical detection by an order of magnitude or more. Filter
fluorometers are also much less expensive.


Excitation Source: A 5-watt quartz-halogen lamp, which emits intense broadband radiation from
340 nm to 750 nm.
Excitation Wavelength Filter: A narrow-band 360-nm filter with a bandpass of 40 nm.
Emission Wavelength Filter: A sharp cut-in, long-wavelength-pass filter which transmits
essentially all light with λ > 415 nm.
Detector: Photomultiplier tube, model 931B PMT.
Detection Limit. Stated in the manufacturer’s literature as 30 ppt quinine sulfate, which is 30
ng/L or about 9 x 10-11 M.

Turn the instrument on at least 15 minutes before using to allow it to warm up and
stabilize. The ON-OFF switch is on the back panel near the power cord. When turned on, the
instrument runs a countdown timer during which it undergoes self tests.


PREPARATION OF SOLUTIONS

Preparation of Stock Sulfuric Acid Solutions

The two stock H2SO4 solutions should have already been prepared for you by the Teaching
Assistants. However, if you use up all of the 0.05 M solution while doing your experiment,
prepare another 2-L batch for those that follow. It is very straightforward.

1 M H2SO4. Slowly and carefully add 56 mL conc. H2SO4 to about 500 mL distilled water in a
1-L beaker with stirring. This solution should have been already prepared for your use.

0.05 M H2SO4. With a graduated cylinder, add 100 mL of 1 M H2SO4 with a graduated cylinder
to about 500 mL of distilled water in the screw-capped acid reagent jug labeled for this solution.
Mix and dilute to the 2.0-L mark on the bottle and mix thoroughly. This solution should already
have been prepared for your use. If you use all of or most of what is there, prepare a new batch
for the students who follow you.

Preparation of Quinine Stock Solution, 1000 ppm

1. Carefully weigh exactly 0.1207 g of quinine sulfate dihydrate onto a folded glassine
weighing paper or into a small plastic weighing boat, and transfer this quantitatively into a
100-mL volumetric flask. A few squirts of distilled water from a wash bottle should help to
wash the solid material from the weighing boat and the neck of the flask.
CHE 226 – Analytical Chemistry Laboratory 35
Quinine
Fluorescence

---

Department of Chemistry

University of Kentucky

2. Pipet 5.00 mL of 1 M H2SO4 (located in hood #2) into the flask. Carefully dissolve all the
quinine in this sulfuric acid solution by swirling before diluting to volume. This is critically
important.

3. Carefully dilute to volume with distilled water and mix thoroughly.

Preparation of Intermediate Quinine Stock Solution, 10.0 ppm

1. Pipet 5.00 mL of the 1000-ppm solution into a 500-mL volumetric flask.

2. Add 25.0 mL of 1 M H2SO4, dilute carefully to volume with distilled water, and mix
thoroughly.

Preparation of Quinine Standard Solutions

1. Using volumetric transfer pipets and/or a 10-mL graduated pipet, add 1.00, 3.00, 5.00, 7.50,
and 10.00 mL of the 10-ppm intermediate stock solution into five properly labeled 100-mL
volumetric flasks. This will result in standard solutions of 0.1, 0.3, 0.5, 0.75, and 1.0 ppm.

2. Carefully dilute to volume with 0.05 M H2SO4.

3. 0.05 M H2SO4 is used as the “blank.”

Preparation of Quinine Unknown

1. Your unknown solution is obtained from the teaching assistants in a 500-mL volumetric
flask. Add 25.0 mL of 1 M H2SO4 to the flask.

2. Dilute to volume with distilled water and mix thoroughly.


PROCEDURE

Turn on the Quantec fluorometer at least 15-20 minutes before making measurements in order to
let it warm up and stabilize.

Measurement of Emission Intensities

1. Carefully fill separate, clean, plastic fluorescence cuvettes (these have 4 clear sides) about ¾
full with the blank (0.05 M H2SO4), each of the five standards, and each unknown sample.
Do not touch the optical surfaces with your fingers. Instead, handle with KimWipes. Be
sure to wipe any smudges off the optical surfaces of the cuvettes.

2. On the main menu of the fluorometer, press ENTER.

CHE 226 – Analytical Chemistry Laboratory 36
Quinine
Fluorescence

---

Department of Chemistry

University of Kentucky
3. Use the right cursor (®) to select “Quinine”. Press RETURN.

4. The instrument asks if you wish to change the name. Select NO.

5. The instrument asks if filters are correct. Select YES.

6. The instrument asks if you would like to you as standard curve from memory. Select NO.

7. The instrument asks for the number of points for the calibration curve. Use the up-arrow ( )
to increase the number to 5 in order to be able to use your five standards. Press RETURN.

8. Beginning with the highest concentration standard, enter the concentration using the up-
arrow to change the values. Use (¬) to move the cursor to the appropriate position. Use the
up-arrow to set the appropriate units (ppm).

9. The instrument asks to insert the sample. Do so and press RETURN.

10. Repeat for other standards.

11. Instrument asks the operator to insert the BLANK. Do so and press ZERO.

12. The instrument gives a “Coefficient of Determination” value. If this value is less than 0.90,
you must pour out your standard solutions and repipet them from the stock quinine solution.
If this value is greater than 0.90, continue.

13. Insert the unknown and Press RETURN.

14. Readout shows READ and provides the value.

15. Repeat the entire process at least two more times to obtain a set of three “good” replicate
measurements: If the values for a set of standards and the unknown do not “drift” over time,
this would mean that the raw fluorescence data for your unknown are within a range of about
3-4% relative. If the values do appear to drift, then the ratios of the fluorescence intensities
of the standard to those of a nearby standard are within a range of about 3-4% relative.

Comparison of Calibration Procedures

This procedure will compare values that are (a) calculated by the instrument based on its internal
calibration procedure with (b) those obtained based on the calibration curve(s) that you prepare
from the raw fluorescence-emission data obtained above.

1. At main menu, select RAW FLUORESCENCE as the units of measure.

2. The instrument requests a value for the standard. Enter the value and RETURN.

CHE 226 – Analytical Chemistry Laboratory 37
Quinine
Fluorescence

---

Department of Chemistry

University of Kentucky
3. The instrument instructs you to insert the standard. USE the 1.0 ppm STANDARD. Do so
and press RETURN. The instrument adjusts its internal gain.

4. The instrument asks “Insert Blank Sample?” Select YES, followed by RETURN.

5. Insert the blank and the instrument will take a reading.

6. Now insert each of the standard solutions and record the emission value for each.

7. Insert the unknown, and record the emission value.

8. Repeat the entire procedure at least twice more in order to obtain at least 3 “good”
measurements for each sample.

9. Prepare calibration curves and calculate the average concentration of the unknown sample.

When done with the entire experiment, rinse out all the plastic cuvettes with distilled water,
shake off excess water, and return them to the experiment drawer so they can be reused.


DATA ANALYSIS

Prepare appropriate calibration curve(s) from your replicate sets of data. Depending on the nature
of the data and any drift in the instrument, it may be best to (a) average all the net emission
intensities for a particular solution and to prepare one calibration curve or (b) prepare several
calibration curves from the separate sets of data, obtain several values for the concentration of
quinine in your unknown, then average these values. Determine which one is better or if both
give equivalent results. Use linear least squares to fit each of the three sets of data, and the
average of all three, in your analysis.

Report the “best value” for the concentration of quinine (in ppm) in your unknown and the
estimated standard deviation of this best value.

Note: By definition, parts-per-million (ppm) is a mass-ratio unit – ganalyte/gsample x 106 or µg/g.
In dilute aqueous solutions, 1 ppm is equivalent to 1 µg/mL or 1 mg/L because the density of the
solution is 1.00 g/mL. A 1000-ppm solution of quinine sulfate (1.000 g of quinine sulfate per
liter of solution) would only be an 828.7 ppm of quinine itself. If you cannot weigh out exactly
0.1207 g of quinine sulfate, try to get it close, and simply calculate the correct values of the
concentrations of your standards.


HAZARDOUS WASTE DISPOSAL

Dispose of ALL waste quinine and sulfuric acid solutions in the proper, labeled Hazardous
Waste Container for this experiment, which is located in the hoods. 0.05 M H2SO4 has a pH
CHE 226 – Analytical Chemistry Laboratory 38
Quinine
Fluorescence

---

Department of Chemistry

University of Kentucky
of about 1 and thus may NOT simply be run down the drain, even if you run large amounts of
water with it. If you are unsure about the container, ASK.

TEXT REFERENCE

D. A. Skoog, D. M. West, F. J. Holler, and S. R. Crouch, Analytical Chemistry: An Introduction,
7th ed., Chapter 23, pp. 594-631.













































Revised January 24, 2005

Copyright © by The Department of Chemistry, University of Kentucky, 2005
CHE 226 – Analytical Chemistry Laboratory 39
Quinine
Fluorescence

---